View HA-4741883_656326.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TM
HA-4741/883
Quad Operational Amplifier
Description
The Intersil HA-4741/883, which contains four amplifiers on a monolithic chip, provides a new measure of performance for general purpose operational amplifiers. Each amplifier in the HA-4741/883 has operating specifications that equal or exceed those of the 741-type amplifier in all categories of performance. The HA-4741/883 is well suited to applications requiring accurate signal processing by virtue of its low values of input offset voltage (3mV max), input bias current (200nA max) and input voltage noise (9nV/Hz typ at 1kHz). The 2.5MHz bandwidth, coupled with high open loop gain, allow the HA-4741/883 to be used in designs requiring amplifiers of wideband signals, such as audio amplifiers. Audio application is further enhanced by the HA-4741/883's negligible output crossover distortion. These excellent dynamic characteristics also make the HA4741/883 ideal for a wide range of active filter designs. Performance integrity of multi-channel designs is assured by a high level of amplifier-to-amplifier isolation (66dB at 10kHz). A wide range of supply voltages (2V to 20V) can be used to power the HA-4741/883, making it compatible with almost any system including battery-powered equipment.
July 1994
Features
* This Circuit is Processed in Accordance to MIL-STD883 and is Fully Conformant Under the Provisions of Paragraph 1.2.1. * Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . 0.9V/s (Min) * Bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . 2.5MHz (Min) * Input Offset Voltage. . . . . . . . . . . . . . . . . . . . 3mV (Max) * Input Bias Current . . . . . . . . . . . . . . . . . . . 200nA (Max) * Input Voltage Noise . . . . . . . . . . . . . . . . . 9nV/Hz (Typ) * No Crossover Distortion * Standard Quad Pinout
Applications
* Universal Active Filters * D3 Communications Filters * Audio Amplifiers * Battery-Powered Equipment
Ordering Information
PART NUMBER HA1-4741/883 HA4-4741/883 TEMPERATURE RANGE -55oC to +125oC -55 C to +125 C
o o
PACKAGE 14 Lead CerDIP 20 Lead Ceramic LCC
Pinouts
HA-4741/883 (CERDIP) TOP VIEW
-IN1 OUT1 -IN1 +IN1 V+ +IN2 -IN2 OUT2 1 2 3 4 5 6 7 + -2 3+ +1 4+ 14 OUT4 13 -IN4 +IN1 12 +IN4 11 V10 +IN3 9 8 -IN3 OUT3 NC V+ NC +IN2 4 5 6 7 8 9 10 11 12 13 OUT2 NC OUT3 -IN2 -IN3 2 +3 -+
HA-4741/883 (CLCC) TOP VIEW
OUT1 OUT4 -IN4 18 +IN4 17 NC 16 V15 NC 14 +IN3 NC
3
2
1 20 19 -+ 4
+1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a trademark of Intersil Americas Inc. Copyright (c) Intersil Americas Inc. 2002. All Rights Reserved
Spec Number
1
511007-883 FN3704
Specifications HA-4741/883
Absolute Maximum Ratings
Voltage Between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . 40V Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15V Voltage at Either Input Terminal . . . . . . . . . . . . . . . . . . . . . . V+ to VOutput Current . . . . . . . . Indefinite (One Amplifier Shorted to GND) Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC Storage Temperature Range . . . . . . . . . . . . . . . . . -65oC to +150oC ESD Rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <2000V Lead Temperature (Soldering 10s). . . . . . . . . . . . . . . . . . . . +300oC
Thermal Information
Thermal Resistance JA JC CerDIP Package . . . . . . . . . . . . . . . . . . . 75oC/W 20oC/W Ceramic LCC Package . . . . . . . . . . . . . . 65oC/W 15oC/W o o Package Power Dissipation Limit at +75 C for TJ +175 C CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.33W Ceramic LCC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.54W Package Power Dissipation Derating Factor Above +75oC CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3mW/oC Ceramic LCC Package . . . . . . . . . . . . . . . . . . . . . . . . 15.4mW/oC
CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Operating Conditions
Operating Temperature Range. . . . . . . . . . . . . . . . -55oC to +125oC Operating Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . 5V to 15V VINCM 1/2 (V+ - V-) RL 2k
TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at: V SUPPLY = 15V, RSOURCE = 100, R LOAD = 500k, VOUT = 0V, Unless Otherwise Specified. GROUP A SUBGROUPS 1 2, 3 Input Bias Current +IB VCM = 0V, +RS = 10k, -R S = 100 VCM = 0V, +RS = 100, -R S = 10k VCM = 0V, +RS = 10k, -R S = 10k V+ = 3V, V- = -27V 1 2, 3 1 2, 3 1 2, 3 1 2, 3 -CMR V+ = 27V, V- = -3V 1 2, 3 Large Signal Voltage Gain +AVOL VOUT = 0V and +10V, RL = 2k VOUT = 0V and -10V, RL = 2k VCM = -10V, V+ = +5V, V- = -25V, V OUT = -10V VCM = +10V, V+ = +25V, V- = -5V, V OUT = +10V 4 5, 6 4 5, 6 1 2, 3 1 2, 3 LIMITS TEMPERATURE +25oC +125oC, -55oC +25oC +125oC, -55oC MIN -3 -5 -200 -325 -200
o
PARAMETERS Input Offset Voltage
SYMBOL VIO
CONDITIONS VCM = 0V
MAX 3 5 200 325 200 325 30 75 -12 -12 -
UNITS mV mV nA nA nA nA nA nA V V V V kV/V kV/V kV/V kV/V dB dB dB dB
-IB
+25oC +125 C, -55 C +25oC +125oC, -55oC +25oC +125oC, -55oC +25 C +125 C, -55 C +25oC +125oC, -55oC +25
oC o o o o
-325 -30 -75 12 12 50 25 50 25 80 74 80 74
Input Offset Current
IIO
Common Mode Range
+CMR
-AVOL
+125oC,
-55oC
Common Mode Rejection Ratio
+CMRR
+25oC +125oC, -55oC +25oC +125oC, -55oC
-CMRR
Spec Number 2
511007-883
Specifications HA-4741/883
TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued) Device Tested at: V SUPPLY = 15V, RSOURCE = 100, R LOAD = 500k, VOUT = 0V, Unless Otherwise Specified. GROUP A SUBGROUPS 4 5, 6 -VOUT1 RL = 10k 4 5, 6 +VOUT2 RL = 2k 4 5, 6 -VOUT2 RL = 2k 4 5, 6 Output Current +IOUT VOUT = -10V 4 5, 6 -IOUT VOUT = +10V 4 5, 6 Quiescent Power Supply Current +ICC VOUT = 0V, IOUT = 0mA VOUT = 0V, IOUT = 0mA VSUP = +5V, V+ = +10V, V- = -15V, V+ = +20V, V- = -15V VSUP = -5V, V+ = +15V, V- = -10V, V+ = +15V, V- = -20V 1 2, 3 1 2, 3 1 2, 3 1 2, 3 LIMITS TEMPERATURE +25oC +125oC, -55oC MIN 12 12 10
o
PARAMETERS Output Voltage Swing
SYMBOL +VOUT1
CONDITIONS RL = 10k
MAX -12 -12 -10 -10 -5 -5 5 7 -
UNITS V V V V V V V V mA mA mA mA mA mA mA mA dB dB dB dB
+25 C +125oC, -55oC +25oC +125 C, -55 C +25 C +125oC, -55oC +25oC +125oC, -55oC
o o
o
10 5 5 -5 -7 80
+25oC +125oC, -55oC +25oC +125oC, -55oC
-ICC
+25oC +125oC, -55oC +25oC +125 C, -55 C +25oC +125oC, -55oC
o o
Power Supply Rejection Ratio
+PSRR
80 80 80
-PSRR
TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at: VSUPPLY = 15V, RSOURCE = 50 , RLOAD = 2k, CLOAD = 50pF, AVCL = +1V/V, Unless Otherwise Specified. GROUP A SUBGROUPS 7 7 7 7 7 7 7 LIMITS TEMPERATURE +25oC +25oC +25oC +25oC +25oC +25oC +25oC MIN 0.9 0.9 2.5 MAX 140 140 40 40 UNITS V/s V/s ns ns % % MHz
PARAMETERS Slew Rate
SYMBOL +SR -SR
CONDITIONS VOUT = -5V to +5V VOUT = +5V to -5V VOUT = 0 to +200mV 10% TR 90% VOUT = 0 to -200mV 10% TF 90% VOUT = 0 to +200mV VOUT = 0 to -200mV VOUT = 50mV
Rise and Fall Time
TR TF
Overshoot
+OS -OS
Gain Bandwidth Product (Small Signal)
GBWP
Spec Number 3
511007-883
Specifications HA-4741/883
TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS Device Characterized at: VSUPPLY = 15V, RLOAD = 5k, CLOAD = 50pF, Unless Otherwise Specified. LIMITS PARAMETERS Differential Input Resistance Full Power Bandwidth Minimum Closed Loop Stable Gain Output Resistance Quiescent Power Consumption Channel Separation SYMBOL RIN FPBW CONDITIONS VCM = 0V VPEAK = 10V RL = 2k, CL = 50pF Open Loop VOUT = 0V, IOUT = 0mA f = 10kHz, RS = 1k Referred to Input AV = 100V/V, VIN = 100mV PEAK NOTES 1 1, 2 TEMPERATURE +25oC +25oC -55oC to +125oC +25oC -55oC to +125oC +25oC MIN 260 14 MAX UNITS k kHz
CLSG
1
1
-
V/V mW
ROUT PC
1 1, 3
-
350 180
CS
1
-66
-
dB
NOTES: 1. Parameters listed in Table 3 are controlled via design or process parameters and are not directly tested at final production. These parameters are lab characterized upon initial design release, or upon design changes. These parameters are guaranteed by characterization based upon data from multiple production runs which reflect lot to lot and within lot variation. 2. Full Power Bandwidth guarantee based on Slew Rate measurement using FPBW = Slew Rate/(2VPEAK). 3. Quiescent Power Consumption based upon Quiescent Supply Current test maximum. (No load on outputs.)
TABLE 4. ELECTRICAL TEST REQUIREMENTS MIL-STD-883 TEST REQUIREMENTS Interim Electrical Parameters (Pre Burn-In) Final Electrical Test Parameters Group A Test Requirements Groups C and D Endpoints NOTE: 1. PDA applies to Subgroup 1 only. SUBGROUPS (SEE TABLES 1 AND 2) 1 1 (Note 1), 2, 3, 4, 5, 6, 7 1, 2, 3, 4, 5, 6, 7 1
Spec Number 4
511007-883
HA-4741/883 Die Characteristics
DIE DIMENSIONS: 87 x 75 x 19 mils 1 mils 2210 x 1910 x 483m 25.4m METALLIZATION: Type: Al, 1% Cu Thickness: 16kA 2kA GLASSIVATION: Type: Nitride Thickness: 7kA 0.7kA WORST CASE CURRENT DENSITY: 1.68 x 105 A/cm 2 SUBSTRATE POTENTIAL (Powered Up): VTRANSISTOR COUNT: 72 PROCESS: Junction Isolated Bipolar/JFET
Metallization Mask Layout
HA-4741/883
-IN4 +IN4 V+IN3 -IN3
OUT4
OUT3
OUT1
OUT2
-IN1
+IN1
V+
+IN2
-IN2
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com Spec Number 5
511007-883

▲Up To Search▲

Price & Availability of HA-4741883

	To Download HA-4741883 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .